The Chariot RTA is the first high-end self-winding vaporizer from the Arcana Mods", which received its final polish in collaboration with PIPELINE.

This vaporizer is designed for both MTL vapers and restrictive DL vapers. The particularly small evaporator chamber is extraordinarily flavorful and develops a dense and lukewarm vapor.

The Chariot RTA has a diameter of 23mm, the tank holds 4ml of liquid.
Thanks to the non-slip top cap of the Chariot RTA, it can be opened with a twist and thus closes the liquid control at the same time.

Four AFC screws (0.8mm, 1.0mm, 1.2mm and 1.4mm) are included in the scope of delivery, which are screwed under the winding.
The fine adjustment or air speed can be adjusted in 6 steps via the AFC ring.

The Chariot RTA is made of very high quality stainless steel (stainless steel 316L) and is delivered with both a PSU and a glass tank.
The positive pole is adjustable. To avoid turning back the positive pole when screwing the Chariot onto a mod, a left-hand thread was installed.
If you want to extend the positive pole, this is also possible by unscrewing the positive pole, removing the insulator (if it sits on the 510 positive pole), attaching a second O-ring (included in the spare part bag) and putting the insulator back again.

This self-winding vaporizer is suitable for advanced MTL vapers.

Notes:
- If you need to disassemble the base of your Chariot RTA, please make sure that the internal "PEEK Silencer" (the air ducts in the direction of the base plate) is correctly aligned during assembly and screw in the positive pole screw before inserting the two Phillips screws.
- For NET Liquids, we recommend the 1.8 mm AFC pin. This is part of the optionally available RDL kit. You can set the desired tensile resistance here using the AFC ring.

ATTENTION: This is a self-winding vaporizer. It is delivered without winding, which must be done by yourself.

Changing instructions Chariot RTA:

COMMISSIONING

- Use a flat-head screwdriver to install the desired AFC screw.
- To open and close the pole screws, we have included a 1.5mm flat-head screwdriver. Prepare a winding (we recommend a winding with an inner diameter of 2.5mm) and position it between the poles. Slide the wire ends into the slots provided and screw the pole screws tightly. Remove the wire ends, they must not come into contact with other components.

INSERT COTTON WOOL

- Gently pull the cotton wool through the wrap.
- Cut both ends of the cotton wool flush with the base or alternatively at an angle.
For an optimal result, we recommend that you cut the cotton wool at an angle.


- Thin out the cotton ends as needed (this is not mandatory for diagonally cut cotton wool) and place them in the cotton pockets provided for this purpose on the deck.
You can now adjust the height of the winding if needed to tailor the vaping experience to your habits. However, we recommend leaving the height of the winding as intended.

OPENING AND FILLING THE TANK

Rotate the tank until the markings on the base and tank are on top of each other to remove the tank from the base. This also gives you access to the winding at any time.
If you turn the tank counterclockwise, the liquid control is opened, if you turn the tank clockwise, the liquid supply is closed.
After the Liquidcontrol is closed, you can remove the topcap by a short counterclockwise turn and fill the tank with liquid through the two slots above the tank.

By turning the tank and the topcap clockwise, the topcap is closed and the liquidcontrol is opened. Your evaporator is now operational.

Dimensions without mouthpiece:

Height: 41mm (without driptip), 59mm (with driptip)
Diameter: 23mm

Material:

- Stainless steel components: 316L
stainless steel - Tank sleeves: PSU and glass
- Insulators: PEEK

Features:

- Filling from the top
- Glass and PSU tank
- Liquid Control (infinitely adjustable)
- Close the LC and remove the topcap with one turn
- Very small evaporator chamber, for a particularly intense taste
- PEEK isolator
- 4 AFC pins
- External Airflow Control (6 levels)
- MTL and RDL (with optionally available AFC pins)
- 316L stainless steel
- Adjustable positive pole (left-hand thread)
- 510 Connector

Scope of delivery:

1 x Chariot RTA with PSU tank
1 x glass tank
4 x AFC screw (0.8mm, 1.0mm, 1.2mm and 1.4mm)
1 x spare parts
1 x leaflet
1 x screwdriver 1.5mm

Warranty and guarantee:

2-year legal warranty.
6 months warranty (not on wear parts)

Electronic cigarettes are not suitable for children and adolescents under 18 years of age, non-smokers, people with
nicotine allergy, people with allergy to propylene glycol, pregnant women and people with cardiovascular diseases.